Packaging Solutions Since 1978

Window Wrapper

Capability
  • Maximum Height = 96″
  • Maximum Width = 84″
  • Maximum Weight 500 Lb.
Construction
  • Turntable:
    • 1/4” steel floor plate, 48” diameter
    • 2-7/8” height form floor.
  • Frame:
    • Structural tube, plate and bar, meet ASTM-A36 or ASTM-A500
    • Fork pockets for in plant movement.
  • Mast:
    • Structural tube, plate and bar, meet ASTM-A36 or ASTM-A500
FILM DELIVERY SYSTEM – KALAMAZOO VARIABLE TENSION Compatibility
  • All commercial stretch films.
  • Adjustable, independent of film roll diameter. Film tension start delay.
  • 10” diameter, 30” web
  Wrap Operation Normal Start Position:
  • Film Lift – DOWN
  • Platen – UP
  1. Operator slides lower fixture to slightly less than the product width, centering on turntable, then sets product on fixture. Position top of product under upper fixture and lower top fixture (platen) to stabilize product.
  2. Operator applies edge protectors as required and attaches film to product by tucking between product and lower fixture.
  3. Operator attaches the film.
  4. Operator returns to console and resets Safety Curtain.
  5. Operator starts wrap cycle.
  6. When system has completed its automatic wrap cycle, the operator cuts the film.
  7. Raise the platen and remove product.
Description of Automatic Wrap Cycle
  • Operator initiates the wrap cycle by pushing the ‘START’ button
  1. Turntable starts.
  2. Film tension comes on gradually.
  3. After bottom reinforcing wraps, the film carriage starts up and travels to the top of product.
  4. Film carriage stops and places the reinforcing wrap on the top.
  5. Film carriage returns to the bottom, the system will decelerate and index to the home position.
Drives
  • Turntable:
    • 1/2 hp. AC variable speed motor with solid state Telemecanique AC Drive controller and inline reducer. #50 chain drive 0-16 RPM
  • Film Lift:
    • 1/2 hp. AC variable speed motor with solid state Telemecanique AC Drive controller and right angle gear reducer. #50 chain drive.
  • Platen:
    • 1/2 hp. AC variable speed motor with solid state Telemecanique AC drive controller and right angle gear reducer. #50 chain drive.
  • Film Tension:
    • 16 ft/lb. 90vDC brake with electronic controller
Electrical Data
  • 110/1/60 15 amp. *Optional voltage 230/1/60 10 amp. 230/3/60 10 amp. or 480/3/60 8 amp.
  • 30” Powered Pre-stretch film delivery
  • Extra Height
  • Extra Length
  • Allen Bradley PLC and Drives
  • Free Standing Control Console
  • System to be used as a pallet stretch wrapper:
    1. Banner Photo-eye Load Height Sensor.
    2. 2-Position selector for Window/Pallet.
    3. Quick removal bottom fixture.
  • Top Platen Load Stabilizer Remote Key Fob and/or Dual Foot Switch
  • Standard Ramp or Wrap Around Ramp
  • Built In Scale
  • Printer w/ 2”x 4” labels 140 per roll. ( 1 case 10 rolls)
  • System to be used as a pallet stretch wrapper:
    • Banner Photo-eye Load Height Sensor.
    • 2-Position selector for Window/Pallet.
    • Quick removal bottom fixture.
  • Safety Rail, Safety Fence, Light Curtain, Interlock Gate Switches
  • Gravity Roller conveyor with manual roller lock.
  • Gravity Roller Popup Conveyors
  • Power requirements 230/1 or 3/60 10 amp.
  • Power requirements 480/3/60 8 amp.
  • Crating (shipping by common carrier)
  • Delivery and Set-up
<!– Video Here –!>